Support for 2Wire 2701 Select another modem Close Select a modem Back Back. Select. Close Select your email program. Close Select your operating system. Run a speed test Troubleshoot my Wi-Fi. What is my Wi-Fi name or password? Access your modem's settings (only accessible from your home)

3800HGV-B Overview The 3800HGV-B is a residential gateway used to connect to the Lightspeed network. It has many of the features of an advanced broadband router as well as some additional features. Following are some of the major features of the 2Wire gateway. The 2wire modem is often bundled with AT&T Internet service, but this brand of modem is not always the best or preferred choice for a home network. Setting the modem to "bridge mode" will allow you to install a third-party router to handle the traffic on your network and the modem will simply function as a direct connection to the phone line. No bridge mode; No 802.11n; Limited access/management of DHCP; No VPN; and above all no Gigabit Ethernet; Basically all of my home PCs are limited based on the 2Wire 3800HGV-B Gateway's antiquated features. 2Wire Item model number 3800hgv-b Item Weight 1.4 pounds Package Dimensions 18 x 14 x 4 inches Manufacturer 2wire ASIN B0042IEZSO Is Discontinued By Manufacturer No Date First Available September 10, 2010 Additional Information. ASIN B0042IEZSO Customer Reviews: 3.6 out of 5 stars 19 ratings. The instructions below may vary slightly depending on the firmware and model number of the 2Wire or Pace gateway you have. Models include but are not limited to the 3800HGV-B, Pace PLC 3801HGV, Pace PLC 5031NV, Pace PLC 5168NV-110, & others. Intermedia cannot do steps 1-6 for you. Bridge mode disables all routing and DHCP services on the device and allows it to function only as a DSL modem. This enables one to use a more feature-rich router behind the 2Wire device. Use the following instructions to configure bridge mode on the 2Wire device. I have cisco 851w router that is connected to att 2wire 3800hgv-b modem (att uverse) in DMZ mode. I configured the cisco router with Cisco Easy VPN. From outside I can establish VPN connection to 851w router using Cisco VPN Client and I can access LAN behind 851w. However, the internet connection go

The U-Verse modem/gateway is a 2WIRE 2701HGV-B; unfortunately you can't put it in bridge mode or turn off DHCP for that matter. Spend quite some time with tech support and we changed the settings so DHCP would give out public IPs but if I use the connection with a link balancer I get some very strange behavior that can be anything from no

I'm sure this question has come up multiple times. I have AT&T U-Verse internet, and with that came the crappy rental 2wire gateway. I have a much better airport extreme that I have connected to the network in bridge mode so I can at least have a modern wireless standard, but I'd rather have my router handle all of the heavy lifting. 2wire provides no warranty with regard to this manual, the software, or other information contained herein and hereby expressly disclaims any implied warranties of merchantability or fitness for any particular purpose with regard to this manual, the software, or such other information, in no event shall 2wire, inc.

I ended up setting it in gateway mode because the internet access doesnt work well in router mode. I set the firewall to accept from router 3 since 2 and 3 are both connected to router 1 and are parallel I had to enter router 3's gateway address from router 1's subnet as router 2 see connections from router one as 10.1.0.3 (router 3's wan address)

Re: Cisco 871 and U-verse 2wire 3800HGV-B Residential Gateway No I have never received a usable answer. Someone in NANOG claimed that he was able to get AT&T to configure his RG in a bridge mode. Posted: Tue Nov 29, 2011 3:47 Post subject: WAN IP issues: Asus RT-N16 --> bridged 2wire 3800HGV-B Post subject: WAN IP issues: Asus RT-N16 --> bridged 2wire If 2wire can not be in bridge mode then ANY router will have to setup same way I am running my R7000 in the DMZ of the ATT 2Wire 3800HGV-B with Uverse. Back to the 2Wire 3800HGV-B Home Services Settings Site Map System Info Broadband LAN Firewall Logs Diagnostics Status Applications, Pinholes and DMZ Advanced Configuration Allow device application traffic to pass through firewall By default, the firewall blocks all unwanted access from the Internet. If the u-verse connection is via PPOE, you can set the 2wire unit to bridge mode, thus only enabling the modem function. From here you would need to setup the PPOE connection in Tomato, etc. Another way to do it would be to leave the exisitng 2-wire unit as is, disable the wireless interface, and then give the router a static IP, and set the 2 Dec 16, 2010 · The heart of the in-building Internet and/or Phone service is the 2Wire Gateway, provided by AT&T. It serves as an Internet modem, VoIP phone gateway, and network router. Plus it enables the set I now want to add a Sonicwall firewall behind the supplied 2wire 3800hgv-b modem/router. I have set up several ATT DSL modems and put them in bridge mode which passes all traffic to the Sonicwall firewalls. It is my understanding and looking at the 2wire config interface that there is no "Bridge Mode".